Handbyggda kök i massivt trä

HOW TO USE THE KITCHEN PLANNER

On the right side of the planner will find four tabs, WALLS, KITCHEN, COLOR and SEND.
Go from left to right, start with WALLS end with SEND.
You can click between these four headings if you need to change something along the way.
Feel free to watch our instructional videos below to understand the kitchen planner a little better.

WALLS TAB

1. Under the heading WALLS:
Start by measuring the width and height of the wall in your kitchen. After you do this, put the dimensions under the heading WALL. You have four walls available walls to sketch on by clicking on wall 2, wall 3, etc. in the menu located on upper left of the page. If you don't have a window or door on the wall, you can click through to the KITCHEN tab.

2. Under the heading WINDOW:
If you have a window on the wall, start by measuring it. Then fill in the dimensions of your window in the width and height fields. Next, enter the values for where you want your window placed on the wall. You do this by measuring from the left side of your wall to the lower left corner of the window. Also measure from the floor to the bottom of the window. Insert these measurements in the corresponding fields.

3.Under the heading DOOR:
If you have a door on the wall, start by measuring it. Next, enter the dimensions of your door in the width and height fields. Following this, enter the location of your door on the wall by measuring from the left side of your wall to the left side of the door. Enter measurements in the corresponding fields.

4. In the sketch surface there are two dotted lines, the bottom line indicates the height of the base cabinets. The top line delineates the gap between the base cabinets and the wall cabinets (default 50 cm). You can adjust this height by dragging the arrows on the left side. Now it's time to click on the "KITCHEN" tab.

KITCHEN TAB

5. Base Cabinets:
At the top you'll find two draggable items, "Filler" and "Cover panel". You can use fillers for example, if you want your kitchen flush against a wall. This would require a filler that is at least 2-5 cm wide placed between the wall and wall adjacent cabinet. To make it easier place the filler first. The filler items can be resized horisontally (width).

Orientation of the handles/knobs, left of right, on certain cabinets can be toggled using the corresponding icons, "L" and "R". Base cabinets can be dragged/repositioned horisontally.

To remove a cabinet from the sketch surface single-click a cabinet and click the "x" icon that appears.
To remove all cabinets from a wall click on "CLEAR WALL"

6. Wall Cabinets:
At the top of the wall cabinets section you'll find two draggable items, "Filler" and "Trim". You can use fillers for example, if you want your kitchen flush against a wall. This would require a filler that is at least 2-5 cm wide placed between the wall and wall adjacent cabinet. To make it easier place the filler first. The filler items can be resized horisontally (width).

"Trim" items can be used if you want your kitchen to be flush with the ceiling. It's easiest to place trim items last, after all cabinets have been placed, so you know how much of an area you need to cover. Trim items can be resized in all directions.

Orientation of the handles/knobs, left of right, can be toggled on certain cabinets using the corresponding icons, "L" and "R". Base cabinets can be dragged/repositioned horisontally.

7. Tall Cabinets:
At the top of the tall cabinets section you'll find two draggable items, "Filler" and "Trim". You can use fillers for example, if you want your kitchen flush against a wall. This would require a filler that is at least 2-5 cm wide placed between the wall and wall adjacent cabinet. To make it easier place the filler first. The filler items can be resized horisontally (width).

"Trim" items can be used if you want your kitchen to be flush with the ceiling. It's easiest to place trim items last, after all cabinets have been placed, so you know how much of an area you need to cover. Trim items can be resized in all directions.

Orientation of the handles/knobs, left of right, can be toggled on certain cabinets using the corresponding icons, "L" and "R". Base cabinets can be dragged/repositioned horisontally.

COLOUR TAB

8. When you feel like you're done with your kitchen, proceed to the "COLOUR" tab. While you have the coulour tab open you select any cabinet sides that you think will need painting. This is done by clicking on the corresponding cabinet side.

Please note that the under side of wall cabinets need to be painted and also their top side if they don't reach up to the ceiling.

When you're done with the color tab, proceed to the "PRICE" tab. Follow the instructions to either save your sketch or send to us for a price quote. Good luck!

Under the heading WALL:
Start by measuring the width and height of the kitchen wall. Round up to the nearest cm. Add the measurements under the heading WALL. Note that all dimensions are in cm. If you have cabinets against more than one wall use the walls selector buttons marked "Wall 1", "Wall 2"...

Under the heading WINDOW:
If you have a window on the wall, start by measuring it. Then fill in the dimensions of your window in the width and height fields. The next step is to place the window in the sketch surface. You do this by measuring from the left of your wall to the bottom of the window left corner. Also measure from the floor to the bottom of the window. Apply these measurements to the fields under the heading PLACE. Observe that all measurements are in cm.

Under the heading DOOR:
If you have a door on the wall, start by measuring it. Then fill in the dimensions of your door in the fields for width and height. The next step is to place the door. You do this by measuring from the left of your wall to the left side of the door. Please note that all measurements are in cm.
Now you see a sketch surface in 2D that shows your wall from the front. In the sketch surface there are two dashed lines, the bottom one is the marking for the height of the base cabinets of 87 cm. The top line shows the space between the base cabinets and walls cabinets (default 50 cm.) You can adjust this height by dragging the arrows on the left side. The standard height for placing wall cabinets is around 50 cm from the top edge of the worktop (1st dashed line). If you choose one of our shallow wall cabinets, the distance can be reduced to 40 cm

Here you will find a list of all our available cabinets organised by type.

BASE CABINETS:
At the top there are filler pieces and cover panels for the base cabinets. Fillers are typically used between a cabinet and a wall, 2-5 cm in width. Start by placing a filler piece on the side where the kitchen will meet the wall before you start placing the cabinets. The filler piece can be dragged sideways to adjust the width. We deliver fillers in 5, 10 and 15 cm widths, rounded up. For cabinets, you choose which side the handle should be on under the image of the cabinet. You can easily move/drag the cabinets in the sketch surface. All options are available under each cabinet. Click on the ones you want and then drag the cabinet into the sketch area.

WALL CABINETS:
At the top of the wall cabinets section you'll find two draggable items, "Filler" and "Trim". You can use fillers if you want your kitchen flush against a wall. This would require a filler that is at least 2-5 cm wide placed between the wall and wall adjacent cabinet. To make it easier place the filler first. The filler items can be resized horisontally (width).We deliver the filler pieces in 5, 10 and 15 cm widths and rounded up. Under the filler pieces you will find "Trim" pieces. Trim items can be used if you want your kitchen to be flush with the ceiling. It's easiest to place trim items last, after all cabinets have been placed, so you know how much of an area you need to cover. Trim items can be resized in all directions. We supply wall cabinet fillers in fixed heights of 10, 20 or 30 cm, rounded upwards. For cabinets, you can choose which side the handle should be on under the image of each cabinet. You can easily move the cabinets around the sketch area.

TALL CABINETS:
At the top of the tall cabinets section you'll find two draggable items, "Filler" and "Trim". You can use fillers for example, if you want your kitchen flush against a wall. This would require a filler that is at least 2-5 cm wide placed between the wall and wall adjacent cabinet. To make it easier place the filler first. The filler items can be resized horisontally (width). "Trim" items can be used if you want your kitchen to be flush with the ceiling. It's easiest to place trim items last, after all cabinets have been placed, so you know how much of an area you need to cover. Trim items can be resized in all directions. Orientation of the handles/knobs, left of right, can be toggled on certain cabinets using the corresponding icons, "L" and "R". Base cabinets can be dragged/repositioned horisontally.

Cabinet doors and panels are always painted. While in the colour tab, click on the edges of cabinets that correspond to any outward facing cabinet sides-sides with no wall or cabinet next to it. Observe that tall cabinets also need to be painted on the underside and on top if they do not go up to the ceiling. We also recommend painting cabinet sides facing the stove, dishwasher and our oven cabinet. You notify your seller directly of the colour at Funkiskök, not in the kitchen planner.

If a base, tall or a seat cabinet has an exposed side, mark the cabinet as both painted and having a visible side inside the COLOR tab. Cabinets marked as having a visible side have no foot mounts and have a panel reaching all the way down to the floor.

To sketch a kitchen island, adjust the wall dimensions (WALL tab) to match the combined dimensions of the island cabinets. For kitchen islands with cabinets facing in only one direction, use the cover panel provided for tall cabinets-one cover panel per cabinet. Alternatively, the kitchen island is comprised of two rows of cabinets that stand back to back to get storage from both ways and a little wider surface. In this case, consider which cabinets should be marked with a visible/painted side (COLOUR tab). Your sales representative at Funkiskök will happily help you with the details.

Since our kitchen planner does not provide a view from above, corner cabinets need a 64 cm wide filler to be placed in the perpendicular wall-see Figure 2. Once this filler is placed use its right edge to place another 5cm filler (see figure 3). This 5 cm filler is used to ensure smooth opening and closing of the corner cabinet doors.

SKETCH CORNER CABINETS FOR WALL CABINETS
For tall corner cabinets use the same procedure as above but allow for 58.5 cm instead of 64 cm.

Single-click on the cabinet and then click the X-icon to remove it. To remove all cabinets from a wall click the CLEAR WALL button.

If you have not previously saved your sketch, clicking the SAVE button will display a form asking you to register your sketch by entering your email adress. Once you have registered your sketch you can choose to send in a price quote or continue with your sketch. Clicking the SAVE button after having registered will continue to save your sketch. Good luck!

It is possible to add multiple sketches. To add an additional sketch click the NEW SKETCH button. In the resulting dropdown menu you can select kitchen series. It is possible to save a total of five sketches. Only one of the sketches can be submitted to for a price quote. For additional price quotes your nearest resellers would be happy to help you with this.

original
Walls
Cabinets
Color
My Info
Wall

Here you enter the length and height of your kitchen walls.

Window

Do you have any windows on the wall where the kitchen will be? Draw them in.
Start by entering the width and height in cm.

Placement

Place the window in the wall. Enter measurements from the left of the wall and bottom-left side of the window.

Door

Do you have any doors in your kitchen wall? Start by entering width and height in cm.

Placement

Place the door in the wall. Enter measurements from the left of the wall and left side of the door.

Base Cabinet - drag & drop on to the sketch surface

Filler
Cover panel
Base Cabinet
BF400L1S
40x
87
x58.5CM
Knife blocks
Knife blocks
Base Cabinet
BF400SL1S
40x
87
x58.5CM
Knife blocks
Knife blocks
Base Cabinet
BF400L3
40x
87
x58.5CM
Knife blocks
Knife blocks
Base Cabinet
BF400SL5
40x
87
x58.5CM
Knife blocks
Knife blocks
Base Cabinet
BF400L5
40x
87
x58.5CM
Knife blocks
Knife blocks
Base Cabinet
BF600L3
60x
87
x58.5CM
Knife blocks
Knife blocks
Base Cabinet
BF300/0D
30x
87
x58.5CM
2 shelves
Base Cabinet
BF200
20x
87
x58.5CM
Base Cabinet
BF400
40x
87
x58.5CM
Base Cabinet
BF600
60x
87
x58.5CM
Base Cabinet
BF600U
60x
87
x58.5CM
Integrated oven
Base Cabinet
BF800
80x
87
x58.5CM
Corner cabinet
Base Cabinet
BF1200
120x
87
x58.5CM
*NOTE: Cabinet depth is 38.5CM
Base Cabinet
BF400L1SS*
40x
87
x38.5CM
Knife blocks
*NOTE: Cabinet depth is 38.5CM
Base Cabinet
BF800S*
80x
87
x38.5CM
Dishwasher panel
450D
45x
87
x1.9CM
*Note: if built-in dishwasher is at an end it needs a cover panel.
Dishwasher panel
600D
60x
87
x1.9CM
*Note: if built-in dishwasher is at an end it needs a cover panel.
Cabinet seat
BF400SB
40x
42
x58.5CM
*NOTE: Cabinet depth is 38.5CM
Cabinet seat
BF400SBS*
40x
42
x38.5CM
Cabinet seat
BF600SB
60x
42
x58.5CM
*NOTE: Cabinet depth is 38.5CM
Cabinet seat
BF600SBS*
60x
42
x38.5CM

Wall cabinet - drag & drop on to the sketch surface

Filler
Trim
Wall cabinet
OF400
40x
90
x31.5CM
2 shelves
Wall cabinet
OF400/Vitrin
40x
90
x31.5CM
2 shelves
Wall cabinet
OF600
60x
90
x31.5CM
2 shelves
Wall cabinet
OF800
80x
90
x31.5CM
2 shelves
Wall cabinet
OF800/Vitrin
80x
90
x31.5CM
2 shelves
Wall cabinet
OF800Special
80x
90
x31521.5CM
2 shelves
Wall cabinet
OF300/0D
30x
90
x31.5CM
2 shelves
Wall cabinet
OF400F
40x
70
x31.5CM
2 shelves
Wall cabinet
OF400F/Vitrin
40x
70
x31.5CM
2 shelves
Wall cabinet
OF600F
60x
70
x31.5CM
2 shelves
Wall cabinet
OF800F
80x
70
x31.5CM
2 shelves
Wall cabinet
OF800F/Vitrin
80x
70
x31.5CM
2 shelves
Wall cabinet
OF300F/0D
30x
70
x31.5CM
2 shelves
Wall cabinet
OF400D
40x
30
x31.5CM
Wall cabinet
OF600D
60x
30
x31.5CM
Wall cabinet
OF800D
80x
30
x31.5CM
*NOTE: Cabinet depth is 21.5CM
Wall cabinet
OF400S*
40x
30
x21.5CM
*NOTE: Cabinet depth is 21.5CM
Wall cabinet
OF600S*
60x
30
x21.5CM
*NOTE: Cabinet depth is 21.5CM
Wall cabinet
OF800S*
80x
30
x21.5CM
Wall cabinet
OF400HD
40x
30
x31.5CM
Wall cabinet
OF600HD
60x
30
x31.5CM
Wall cabinet
OF800HD
80x
30
x31.5CM
*NOTE: Cabinet depth is 21.5CM
Wall cabinet
OF400HS*
40x
30
x21.5CM
*NOTE: Cabinet depth is 21.5CM
Wall cabinet
OF600HS*
60x
30
x21.5CM
*NOTE: Cabinet depth is 21.5CM
Wall cabinet
OF800HS*
80x
30
x21.5CM
Corner cabinet
OF300HH
60x
30
x31.5/58.5CM
Corner cabinet
OF700HH
60x
70
x31.5/58.5CM
2 shelves
Corner cabinet
OF900HH
60x
90
x31.5/58.5CM
2 shelves
*NOTE: Cabinet depth is 21.5/58.5CM
Corner cabinet
OF300HHS*
60x
30
x21.5/58.5CM
*NOTE: Cabinet depth is 21.5CM
Redahylla
REDA400*
40x
13.8
x21.5CM
*NOTE: Cabinet depth is 21.5CM
Redahylla
REDA600*
60x
13.8
x21.5CM

Tall cabinet - drag & drop on to the sketch surface

Filler
Cover panel
Trim
Tall cabinet
HF2000K
60x
200
x60CM
Fridge & Freezer
Tall cabinet
HF2000K/2D
60x
200
x60CM
Fridge & Freezer
Tall cabinet
HF2000
60x
200
x60CM

Top

Bottom

Wardrobe/Cleaning cabinet
HF2000G/S
60x
200
x60CM
Tall cabinet oven
HF2000U
60x
200
x60CM

Top

Bottom

*NOTE: Cabinet depth is 40CM
Tall cabinet
HF2000S*
60x
200
x40CM

Top

Bottom

Tall cabinet
HF2000/2D
60x
200
x60CM

Top

Bottom

*NOTE: Cabinet depth is 40CM
Tall cabinet
HF2000/2D/S*
60x
200
x40CM

Top

Bottom

Tall cabinet
HF300
60x
30
x60CM
*NOTE: Cabinet depth is 40CM
Tall cabinet
HF300S*
60x
30
x40CM
Tall cabinet
HF500
60x
50
x60CM
1 shelf 2/3
*NOTE: Cabinet depth is 40CM
Tall cabinet
HF500S*
60x
50
x40CM
1 shelf
Tall cabinet
HF600
60x
60
x60CM
1 shelf 2/3
*NOTE: Cabinet depth is 40CM
Tall cabinet
HF600S*
60x
60
x40CM
1 shelf
Tall cabinet
HF2000/4
40x
200
x60CM

Top

Bottom

*NOTE: Cabinet depth is 40CM
Tall cabinet
HF2000/4/S*
40x
200
x40CM

Top

Bottom

Tall cabinet
HF2000/4/2D
40x
200
x60CM

Top

Bottom

*NOTE: Cabinet depth is 40CM
Tall cabinet
HF2000/4/2D/S*
40x
200
x40CM

Top

Bottom

Tall cabinet
HF300/4
40x
30
x60CM
*NOTE: Cabinet depth is 40CM
Tall cabinet
HF300/4/S*
40x
30
x40CM
Tall cabinet
HF500/4
40x
50
x60CM
1 shelf 2/3
*NOTE: Cabinet depth is 40CM
Tall cabinet
HF500/4/S*
40x
50
x40CM
1 shelf
Tall cabinet
HF600/4
40x
60
x60CM
1 shelf 2/3
*NOTE: Cabinet depth is 40CM
Tall cabinet
HF600/4/S*
40x
60
x40CM
1 shelf
Help

Painted side

Select the cabinet side to be painted by clicking on the corresponding side. We recommend painting sides facing a stove, dishwasher and our oven cabinet.

Save your Sketch

Vill du spara din ritning och fortsätta en annan dag? Klicka på spara skiss knappen och skriv in din e-postadress så mailar vi dig din länk.